|
 |
Current location:home>>product central |
|
Ceramic ball mill |
| Ceramic ball mill mainly used mix or mill the material. The fine sizes are even and can save force, too. It has two types: wet mill and dry mill. The machine could use the different line according to the product requirement to satisfy different requirement. The milling fineness depends on the milling time. The motor is started by the coupling reduce voltage. The structure is divided into integral type and freestanding type. It has the following advantages: lower investment, energy saving, structure novelty, simple operation, steady and reliable performance. It is suitable to mill the mixture of general and especial material. Users could choose the proper type, liner and media according to different material ratio, rigidity and output size.
|
 |
|
|
|
Flotation machine |
| This type of flotation machine is made up of U through solid, hollow shaft inflation, suspension rotor and new type impeller. The cone impeller lean backwards, the blending quantity is big and the pressure head is small, the advantages are: simple structure and low energy consumption. Inside the impeller, there is air distributor, which distributes air into most parts of impeller evenly. |
|
|
|
|
Cement mill |
| Structure:
The machine is composed by feeding part, discharging part, rotary part and transmission part (reducer, small drive gear, electric motor and electric cabinet). The hollow shaft is cast steel and the liner is changeable. The rotary gearwheel adopts casting hobbing process and the drum is equipped with wear-resistant liner, which has good wear-resistance. The machine works stably.
Note: According to different materials and discharging methods, the users can choose between dry type and wet lattice-shaped type.
|
|
|
|
|
Raw material mill |
| Structure:
The machine is composed by feeding part, discharging part, rotary part and transmission part (reducer, small drive gear, electric motor and electric cabinet). The hollow shaft is cast steel and the liner is changeable. The rotary gearwheel adopts casting hobbing process and the drum is equipped with wear-resistant liner, which has good wear-resistance. The machine works stably.
Note: According to different materials and discharging methods, the users can choose between dry type and wet lattice-shaped type. |
|
|
|
|
Spiral chute |
| Combining the characteristics of spiral concentrator, spiral chute, shaking table and centrifugal concentrator, spiral chute of glass steel was made in 1977 and is a best choice of mineral selecting, especially suitable near the sea, river, beach and brook. It has the characteristics of rational structure, simple installation, small floor space, easy operation, stable dressing, low noise, clear separation, big capacity, high efficiency and high recovery rate. It is not heavy and moisture proof, rusty proof and acid anti-corrosive. It has few requirements on the feed amount, density, granularity and ore grade. |
|
|
|
|
Coal pulverizer |
| Coal pulverizer of MG type is one of four main auxiliary engines in steam power plant and main equipment of coal powder system. It is mainly used to mill coal blocks of different rigidity and also to manufacture powder in industries of cement, metallurgy and chemical.
|
|
|
|
|
Ball mill |
| Energy-saving ball mill is a key milling machine after the material is crushed. It is widely used to mill different kinds of mineral ores and other rubbing materials in these industries of cement plant, silicate industry, new construction material, refractory material, chemical fertilizer, ferrous and nonferrous metals, glass as well as ceramics. There are two milling types: wet and dry. |
|
|
|
|
Disk pelletizer |
| Rotary dryer is widely used to dry slag, clay and other materials in building materials, metallurgy, and chemical industry. The machine is made up of gyrator, material raising plate, transmission, support device and seal ring. It has the features of reasonable structure, excellent manufacture, high yield, low energy consumption, steady revolution and easy operation. |
|
|
|
|
Disk feeder |
| Disk feeder can convey the powdered materials below 20mm in size. It is made up of transmission, feeder, measurable belt conveyor and measuring device. The feeder and belt conveyor is driven by a driving unit. The magnetic clutch on the driving unit has the function of feeder starting or stopping and switching between them. The speed of measurable belt conveyor is smaller than 1meter per second. The tachometer is fixed to measure the belt speed and the measuring pole is fixed to adjust the weighing roller when it is not in the proper position. |
|
|
|
|
|
